Heidenhain TNC 640 (34059x-04) Cycle programming Instrukcja Użytkownika Strona 348
- Strona / 603
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Cycles: Turning
13.16 SIMPLE RADIAL RECESSING
(Cycle 841, DIN/ISO: G841)
13
348
TNC 640 | User's Manual Cycle Programming | 3/2014
Finishing cycle run
1 The TNC positions the tool at rapid traverse to the first slot side.
2 The TNC finishes the side wall of the slot at the defined feed
rate Q505.
3 The TNC finishes the slot floor at the defined feed rate.
4 The TNC returns the tool at rapid traverse.
5 The TNC positions the tool at rapid traverse to the second slot
side.
6 The TNC finishes the side wall of the slot at the defined feed
rate Q505.
7 The TNC positions the tool back at rapid traverse to the cycle
starting point.
Please note while programming:
Program a positioning block to the starting position
with radius compensation R0 before the cycle call.
The tool position at cycle call defines the size of the
area to be machined (cycle starting point).
From the second infeed, the TNC reduces each
further cutting traverse by 0.1 mm. This reduces
lateral pressure on the tool. If the offset width Q508
was input into the cycle, the TNC reduces the cutting
traverse by this value. After clearance roughing, the
remaining material is removed with a single cut. The
TNC generates an error message if the lateral offset
exceeds 80 % of the effective cutting width (effective
cutting width = cutting width –2*cutting radius).
- User’s Manual 1
- Cycle Programming 1
- About this Manual 4
- Software options 5
- Intended place of operation 9
- Legal information 9
- Fundamentals 10
- Contents 13
- Overviews 47
- 1.1 Introduction 48
- Available Cycle Groups 1.2 49
- 1.2 Available Cycle Groups 49
- Using Fixed Cycles 51
- 2.1 Working with fixed cycles 52
- Working with fixed cycles 2.1 53
- Using GLOBAL DEF information 57
- Entering PATTERN DEF 61
- Using PATTERN DEF 61
- Defining a single pattern 63
- Defining a full circle 65
- Point tables 2.4 67
- 2.4 Point tables 67
- Drilling 71
- 3.1 Fundamentals 72
- DRILLING (Cycle 200) 3.3 75
- 3.3 DRILLING (Cycle 200) 75
- ISO: G203) 82
- ISO: G205) 88
- 3.9 BORE MILLING (Cycle 208) 92
- BORE MILLING (Cycle 208) 3.9 93
- (Cycle 241, DIN/ISO: G241) 95
- Programming Examples 3.11 99
- Fixed Cycles: Drilling 100
- 3.11 Programming Examples 100
- Fixed Cycles: 101
- Tapping / Thread 101
- 4.1 Fundamentals 102
- (Cycle 206, DIN/ISO: G206) 103
- Cycle parameters 105
- ISO: G207) 106
- 209, DIN/ISO: G209) 109
- Prerequisites 113
- Cycle run 115
- (Cycle 263, DIN/ISO:G263) 119
- 264, DIN/ISO: G264) 123
- Q359 (incremental): 126
- (Cycle 265, DIN/ISO: G265) 127
- DIN/ISO: G267) 131
- Programming Examples 4.11 135
- 4.11 Programming Examples 135
- Fixed cycles: 137
- Pocket milling / 137
- 5.1 Fundamentals 138
- DIN/ISO: G251) 139
- ISO: G252) 143
- DIN/ISO: G256) 156
- 5.8 Programming Examples 164
- Programming Examples 5.8 165
- Pattern Definitions 167
- 6.1 Fundamentals 168
- 6.4 Programming Examples 174
- Programming Examples 6.4 175
- Contour Pocket 177
- Fixed Cycles: Contour Pocket 178
- 7.1 SL Cycles 178
- SL Cycles 7.1 179
- Superimposed contours 7.3 181
- 7.3 Superimposed contours 181
- ISO G275) 197
- Programming Examples 7.11 201
- 7.11 Programming Examples 201
- Cylindrical Surface 207
- 8.1 Fundamentals 208
- Cycle call 209
- 8.5 Programming Examples 218
- Programming Examples 8.5 219
- Defining contour descriptions 224
- Superimposed contours 226
- Contour description programs: 231
- Multipass Milling 235
- 10.1 Fundamentals 236
- ISO: G230) 237
- Q236=+25 ;4TH POINT 3RD AXIS 242
- Q240=40 ;NUMBER OF CUTS 242
- Q207=500 ;FEED RATE FOR 242
- Programming Examples 10.6 255
- 10.6 Programming Examples 255
- Cycles: Coordinate 257
- Transformations 257
- 11.1 Fundamentals 258
- (Cycle 7, DIN/ISO: G53) 260
- Configuring the datum table 264
- To exit a datum table 264
- Status displays 264
- G80, software option 1) 273
- Resetting 275
- Workspace monitoring 276
- Programming Examples 11.10 279
- 11.10 Programming Examples 279
- Cycles: Special 281
- Functions 281
- Cycles: Special Functions 282
- 12.1 Fundamentals 282
- Function 283
- ISO: G36) 286
- Cycle function 287
- 12.6 ENGRAVING (Cycle 225 290
- DIN/ISO: G225) 290
- Cycles: Turning 293
- Working with turning cycles 297
- Application 300
- (Cycle 800, DIN/ISO: G800) 301
- (Cycle 811, DIN/ISO: G811) 308
- Roughing cycle run 310
- (Cycle 812, DIN/ISO: G812) 311
- (Cycle 813, DIN/ISO: G813) 314
- TURN, LONGITUDINAL PLUNGE 315
- (Cycle 814, DIN/ISO: G814) 318
- (Cycle 810, DIN/ISO: G810) 322
- 13.10 TURN CONTOUR-PARALLEL 326
- (Cycle 815, DIN/ISO: G815) 326
- 13.11 TURN SHOULDER FACE 330
- (Cycle 821, DIN/ISO: G821) 330
- (Cycle 822, DIN/ISO: G822) 332
- TURN SHOULDER FACE EXTENDED 333
- (Cycle 823, DIN/ISO: G823) 336
- TURN, TRANSVERSE PLUNGE 337
- (Cycle 824, DIN/ISO: G824) 340
- 13.15 TURN CONTOUR FACE 344
- (Cycle 820, DIN/ISO: G820) 344
- (Cycle 841, DIN/ISO: G841) 348
- SIMPLE RADIAL RECESSING 349
- (Cycle 842, DIN/ISO: G842) 350
- RADIAL RECESSING EXTENDED 351
- (Cycle 840, DIN/ISO: G840) 354
- RECESSING CONTOUR RADIAL 355
- 13.19 SIMPLE AXIAL RECESSING 358
- (Cycle 851, DIN/ISO: G851) 358
- SIMPLE AXIAL RECESSING 359
- (Cycle 852, DIN/ISO: G852) 362
- AXIAL RECESSING EXTENDED 363
- 13.21 AXIAL RECESSING 366
- (Cycle 850, DIN/ISO: G850) 366
- AXIAL RECESSING 367
- 13.22 RADIAL RECESSING 370
- (Cycle 861, DIN/ISO: G861) 370
- RADIAL RECESSING 371
- (Cycle 862, DIN/ISO: G862) 372
- (Cycle 860, DIN/ISO: G860) 376
- 13.25 AXIAL RECESSING 380
- (Cycle 871, DIN/ISO: G871) 380
- (Cycle 872, DIN/ISO: G872) 382
- 13.27 AXIAL RECESSING 386
- (Cycle 870, DIN/ISO: G870) 386
- 13.28 THREAD LONGITUDINAL 390
- (Cycle 831, DIN/ISO: G831) 390
- THREAD LONGITUDINAL 391
- ISO: G832) 392
- =0 ISO 1502 394
- 13.30 CONTOUR-PARALLEL THREAD 396
- (Cycle 830, DIN/ISO: G830) 396
- CONTOUR-PARALLEL THREAD 397
- 13.31 Example program 400
- Example program 13.31 401
- Using Touch Probe 403
- Using Touch Probe Cycles 404
- Probe Cycles 407
- Multiple measurements 409
- Touch probe table 14.3 411
- 14.3 Touch probe table 411
- Touch Probe 413
- Cycles: Automatic 413
- Measurement 413
- Misalignment 413
- 15.1 Fundamentals 414
- Fundamentals 15.1 415
- (Cycle 401, DIN/ISO: G401) 419
- (Cycle 402, DIN/ISO: G402) 422
- ISO: G403) 426
- ISO: G404) 428
- (Cycle 405, DIN/ISO: G405) 430
- Datum Setting 435
- 16.1 Fundamentals 436
- Fundamentals 16.1 437
- ISO: G408) 440
- DIN/ISO: G409) 444
- (Cycle 410, DIN/ISO: G410) 447
- Q384=+0 ;3RD CO. FOR TS AXIS 450
- Q333=+1 ;DATUM 450
- 16.5 DATUM FROM OUTSIDE OF 451
- RECTANGLE (Cycle 411, DIN/ 451
- ISO: G411) 451
- (Cycle 412, DIN/ISO: G412) 454
- (Cycle 413, DIN/ISO: G413) 459
- (Cycle 414, DIN/ISO: G414) 463
- (Cycle 415, DIN/ISO: G415) 468
- DIN/ISO: G416) 472
- Q382=+85 ;1ST CO. FOR TS AXIS 475
- Q383=+50 ;2ND CO. FOR TS AXIS 475
- Q320=0 ;SET-UP CLEARANCE 475
- 417, DIN/ISO: G417) 476
- 418, DIN/ISO: G418) 478
- ISO: G419) 482
- Workpiece 489
- Inspection 489
- 17.1 Fundamentals 490
- Fundamentals 17.1 491
- DIN/ISO: G422) 504
- 17.7 MEASURE RECTANGLE INSIDE 507
- (Cycle 423, DIN/ISO: G423) 507
- (Cycle 424, DIN/ISO: G424) 510
- DIN/ISO: G425) 513
- DIN/ISO: G426) 516
- DIN/ISO: G427) 519
- (Cycle 430, DIN/ISO: G430) 522
- Q309=0 ;PGM STOP IF ERROR 524
- Q330=0 ;TOOL 524
- 17.14 Programming Examples 528
- Programming Examples 17.14 529
- 18.1 Fundamentals 532
- MEASURE (Cycle 3) 18.2 533
- 18.2 MEASURE (Cycle 3) 533
- DIN/ISO: G461) 541
- 462, DIN/ISO: G462) 542
- (Cycle 463, DIN/ISO: G463) 544
- Kinematics 547
- Overview 549
- 19.2 Prerequisites 550
- DIN/ISO: G450, option) 551
- Logging function 552
- Notes on data management 553
- DIN/ISO: G451, option) 554
- Positioning direction 556
- Notes on the accuracy 559
- Backlash 561
- Various modes (Q406) 566
- DIN/ISO: G452, option) 568
- Drift compensation 575
- Tool Measurement 579
- 20.1 Fundamentals 580
- Fundamentals 20.1 581
- Tables of Cycles 595
- 21.1 Overview 596
- Overview 21.1 597
- Touch probes from HEIDENHAIN 603
Powiązane produkty i podręczniki dla Ekwipunek Heidenhain TNC 640 (34059x-04) Cycle programming
(607 strony)
(615 strony)
(623 strony)
(627 strony)
(645 strony)
(647 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji